This automated optical Fiber tensile screening program is designed for operator skill impartial use within creation and lab configurations. Two basic model configurations allow the consumer to select between a set up for standard linear Proof screening and with additional mandrels for rotary high strength screening.
The linear version is designed for creation Proof screening with causes as much as 22 N. Motorized clamps with carefully designed rubber inserts be sure that the Optical Fiber Ribbon Machine is not ruined inside the screening process while simultaneously eliminating the need for an outside air supply. Degrees of pulling force, pulling velocity and hold time are automated and conveniently offered to the operator through the built-in LCD touchscreen display manage. Information from tests can be stored and accessed through the Universal serial bus dock or Ethernet user interface.
Mandrels the exact same style as with NYFORS’ optical Fiber recoaters can be installed on the Proof tester in the rotary high power settings. The Fiber is covered across the two mandrels which assistance it having a unique clamping mechanism. By doing this greater loads can be used onto the Fiber, enabling breaking power assessments under controlled circumstances.
Changeable clamp positioning facilitates screening using the greatest force levels as well as screening of short Fiber lengths. The lightweight and light bodyweight style helps make the instrument simple to move around in a lab atmosphere and also to incorporate in a creation work table where space are at a premium. The equipment is actually a lightweight and light-weight tool ideal for screening the potency of visual fibers as much as 30 N. The equipment is designed to meet all types of programs when a strength test must be performed.
The device was created with all the user in mind. The Secondary Coating Line is definitely put into the guided linear clamps, and also the testing starts instantly with a “One Touch” go button. The built-in microprocessor regulates all the essential guidelines including tugging force, tugging velocity and hold time. This permits to get a completely controlled test every time.
The equipment can be connected to an external PC, which allows usage of all automated guidelines and settings. The equipment is tailored to face-on your own use or to the incorporation into different subsystems. The device comes with an extensive capability of signing and saving information such as tugging force, tugging velocity and Fiber size and other parameters.
Two recoat injector configurations are available. The PTR307 uses an automated pump to inject the recoat material. The amount of materials dispensed through the automated injector is managed by hand using the top-mounted “Inject” switch or programmed to the device utilizing the tablet controller. The PTR307B comes with a handbook recoat shot program that will require the user to personally distribute the recoat materials in to the mold cavity; a replacement injector for the PTR307B recoater is accessible below. Make sure you note that this automated injector is just compatible with higher-directory recoat materials, while the manual injector works with each low- and- index recoat materials; both are sold separately below. Please contact Tech Assistance for more information.
he manual injector can be mounted to compatible Fiber recoaters through the 4-40 screws on the recoater housing (see photo to the right). Utilize a 3/32″ hex key to safe the injector prior to use. To connect the PTRRRM to the recoater mold, tighten the connector at the conclusion of the green plastic material tubing, then release by way of a 1/4 choose enable rotation.
The injector is equipped with a syndication device and 2-position selection handle for directing the stream of recoat material. A knurled dispensing screw with an internal plunger works as a syringe for the recoat materials. To fill up the syringe, point the lever downwards (i.e., toward the recoat container), then spin the knurled dispensing screw counterclockwise till it spins easily to fill up the syringe (demonstrated within the photo towards the right). Then, to inject the recoat materials in to the mold, point the lever horizontally (i.e., dealing with qyjflh knurled attach) and spin the attach clockwise till near the end from the travel range is achieved. Avoid bottoming out your dispenser because this may harm the internal plunger; also take care when re-interesting the threads in order to avoid cross threading the dispensing screw. Several fill/inject actions may be required until air is displaced inside the system. Use camera lens tissue plus an acetone or alcohol cleaning solution to gather Optical Fiber Coloring Machine materials that flows from the mold.